啊啾哇MLT197其它
【数字标牌行业门户网站】 服务热线:400-6787-360 |欢迎投稿 |会员登录 |免费注册 |设为首页 |加入收藏 |RSS |客户服务
数字标牌也称数字告示或多媒体信息发布系统
啊啾哇MLT197其它
 当前位置:首页 > 产品大全 > 其它 > 啊啾哇 > MLT197
联系方式
深圳市皓凯迪电子科技有限公司
电话:86-755-27967959-619
地址:宝安区新安35区塘坊花园一巷4号A1栋3楼
网址:http://www.szhkdlcd.com\www.aquav.cn
推荐品牌
啊啾哇MLT197其它
其它品牌列表
AXD安信达 Elo
KingSpec NEXCOM
啊啾哇 金士顿
英康仕 英特尔
其它相关链接
>> 浏览相关资讯 >> 浏览相关产品
>> 浏览相关商家 >> 浏览相关商机
关于品牌收录
数字标牌网产品中心收录全球知名其它品牌,欢迎登录数字标牌网产品中心查找其它产品。
如果在此找不到贵企业的产品品牌请您联系我们:
电话:0755-33019199(十二线)
邮箱:ds-360@3v.cn
如果您对数字标牌网其它产品专区有好的意见或建议请您及时联系我们。
产品分类导航
多媒体信息发布系统电子看板
网络广告机液晶广告机
车载广告机高清机顶盒
户外大屏幕互动式广告载体
流媒体实时发布系统播放器
嵌入式流媒体服务器数字标牌显示器
触控一体机数字标牌软件
嵌入式主板广告机外壳
触摸屏透明屏
其它
啊啾哇MLT197其它
啊啾哇MLT197其它 产品简介
Input voltage range 输入电压 90Vac to 264Vac 
Normal voltage range 标称输入 100Vac to 240Vac 

产品报价:110元
啊啾哇MLT197其它详细介绍
峰值电流或功率的测试是在其它

额定负载时测试,且脉宽小于 100 毫秒。


1.2.2  Table 3 DC Output Ripple & Noise. (输出纹波和噪声)


Output Voltage Ripple & Noise (Max.)
+V1(+24V) 300mVp-p@25℃; 450mVp-p@-10℃
+V2(+12V) 150mVp-p@25℃; 300mVp-p@-10℃
+5.0V 60mVp-p@25℃; 150mVp-p@-10℃;
+5.0V(SB) 60mVp-p@25℃; 200mVp-p@-10℃; 150mVpp when STB

Note: 1) Measurements shall be made with an oscilloscope with 20MHz bandwidth.

示波器须设置在 20 兆赫兹带宽

2) Outputs shall be bypassed at the connector with a 0.1uF ceramic capacitor and a 10uF electrolytic capacitor to simulate system loading.


输出须并联 0.1uF 的陶瓷电容和 10uF 的电解电容来模拟负载





1.2.3  Output Transient Response. (输出动态响应)

Table 4. Test condition.测试条件

Voltage Tolerance Limit Slew Rate Load Change
5.0V/5.0VS±5% 0.2A/uS Min. to 50% load and 50% to Max load
24V/12V/±10%    
All output±10% 0.2A/uS Min. load to Max load


Note:Transient response measurements shall be made with a load changing

repetition rate of 50Hz to 10kHz.

           1.2.4  Table 5 DC Output Hold-Up Time. (输出保持时间)
Output Voltage 120Vac input 220Vac input
+V1(+24V) ≥10 mS ≥10 mS
+V2(+12V) ≥10 mS ≥10 mS
+5.0V ≥10mS ≥10 mS
+5.0V(STB) ≥10 mS ≥10 mS

Note: All of dc output at full load. 所有输出带满载

1.2.5  Table 6  DC Output Overshoot At Turn On & Turn Off.(输出超调)

Output Channel Output(V) Over shoot voltage(V)超调电压
Turn on 开机 Turn off 关机
+V1(+24V) + 24V 10% 10%
+V2(+12V) + 12V 10% 10%
+5.0V +5.0V 10% 10%
+5.0V(SB) +5.0V 10% 10%

Note:  All of dc output current    from    Min. to Max. 测试时负载范围:最小到最大

1.2.6  Table 7 DC output voltage rise time(输出上升时间)
Output Voltage 120Vac input   &FullLoad 220Vac input &Full Load
+V1(+24V) ≤100mS ≤100mS
+V2(+12V) ≤100 mS ≤100 mS
+5.0V ≤100 mS ≤100mS
+5.0V(SB) ≤50 mS ≤50 mS

Note: The output voltages shall rise    from   10% to 90% of their output voltage.

输出从 10%上升到 90%的时间







1.3  Remote On/Off Control:(遥控功能)

The power supply DC outputs (without +5.0Vsb) shall be enable with an active-high
TTL(≥2.5V/2.0mA)-compatible signal(Ps-on). The +5.0Vsb is on whenever the AC power is present.

除 5.0Vsb 外,其余输出受控于一个 TTL 电平兼容的信号(Ps-on≥2.5V/2.0mA), 5.0Vsb 上电就存在。

Ø When Ps-on is pulled to TTL high, the DC outputs are to be enabled. Ps-on 高电平,打开输出 

Ø When Ps-on is pulled to TTL low or open circuit, the DC outputs are to be 

disabled.

Ps-on 低电平,关闭输出

Table 8.

Ps-on Signal Comments Outputs
Ps-on- high ≥2.5V&2.0mA ( source) Output
Ps-on- low ≤ 0.5V X
Ps-on-open -- X


1.4 Protection: (保护功能) 

1.4.1 Table 9  DC output Over Voltage Protection. (输出过压保护) 

Output Voltage TYP. Over Voltage Comments
+V1(+24V) 28V Power supply latch into shutdown state
输出锁机
+V2(+12V) 15V Power supply latch into shutdown state
输出锁机

Note: The power supply shall be test at max AC voltage (264Vac) and min load or no load.
应该在最大交流输入电压 264 伏和轻载、空载下测试。

1.4.2 Table 10  DC Output Over current Protection. (输出过流保护)

Output Voltage Over Current Comments
+V1(+24V) ≥8.5Atyp* Power supply latch into shutdown state
输出锁机
+V2(+12V) ≥4.5Atyp* Power supply latch into shutdown state
输出锁机
+5V ≥4Atyp* Hiccup 尝试重复启动
+5.0VSB ≥1.5Atyp* Hiccup 尝试重复启动

Note:* The over current protection should be test at other of dc output at Rated load

过流保护测试是在其它额定负载时测试.







1.4.3 Table 11  DC Output Short Circuit Protection. (输出短路保护)

Output Voltage Comments
+V1(+24V) Shutdown 关机
+V2(+12V) Shutdown 关机*
+5V Shutdown 关机*
+5.0V(SB) Hiccup 尝试重复启动

Note:* The Short Circuit protection should be test at other of dc output at Rated load

短路保护测试是在其它额定负载时测试.

1.4.4 Re   set    After Shutdown.(保护功能复位)

Recycle the ps-on signal, the power supply will restart after the fault removed,But +5V、+5.0V(STB)output over voltage can’t be re   set   .

故障去除后,关掉 Ps-on 信号再打开,电源即可恢复。+5V、+5.0V(STB)过压后不可恢复。


2. Isolation(绝缘性能) 

2.1 Table 12 (绝缘阻抗) 

Input To Output DC500V 10MΩmin (at room temperature)
Input To FG DC500V 10MΩmin (at room temperature)
Output To FG Non Isolated

2.2  Table 13 (绝缘耐压)

Input To Output 3000Vac 50Hz 1minute ≤10mA
Input To FG 1500Vac 50Hz 1minute ≤10mA
Output To FG Non Isolated

Note:  Open FG and Output return. 交流地和输出负极要断开。

3. Safety (安全规格)

The power supply shall compliance with the following Criterion:

电源安全性满足下列标准

1) UL60950 

2) EN60950 

3) GB4943-1995 

4. EMC (电磁兼容性) 

4.1 EMI (电磁干扰) 

The power supply shall compliance with the following Criterion:

电源电磁干扰满足下列规则:

1) Conduction Emission : (传导干扰度) *EN55022, CLASS  B 

*GB9254, CLASS    B 
*FCC PART15 CLASS    B 

2) Radiated Emission : (辐射干扰度) *EN55022, CLASS  B 

*GB9254, CLASS B 
*FCC PART15 CLASS   B 

4.2 EMS (电磁抗扰) 

The power supply shall compliance with the following Criterion:

电源电磁抗扰满足下列规则:

1) ESD (静电抗扰度)
*GB17626.2-1998/IEC61000-4-2
2) EFT (脉冲群抗扰度)
*GB17626.4-1998/IEC61000-4-4  3KV
3) Surge (雷击浪涌)
*GB17626.5-1998/IEC61000-4-5 1.5KV / 3KV


5. Environmental Requirement (工作环境) 

5.1 Temperature (环境温度)

ü Operating:0℃ to +40℃.
ü Store:-20℃ to +80℃.

5.2 Humidity (环境湿度)

ü Operating:    from    10%to90% relative humidity (non-condensing). 
ü Store:    from    5 to 95% relative humidity (non-condensing). 

5.3 Altitude (海拔高度)

ü  Operating:  to10,000 ft.

ü Store:to 20,000ft.

5.4 Cooling Method (冷却方式)

ü Ventilation cooling . 自然冷却 

5.5 Vibration (振动耐受) 

ü 10-55Hz, 19.6m/s2(2G), 3minutes period, 60minutes each along X, Y and Z axis. 

5.6 Impact (冲击耐受) 

ü 49m/s2(5G),11ms, once each X, Y and Z axis. 
6. Dimension (物理尺寸) 

ü 192mm X 130mm X30mm (长 L *宽 W * 高 H ). 

7. Weight (重量) 

ü 500g 

7. Pin Connection (连接器脚位定义) 

Table 15  Pin-CON5 Connection And Function

NO. Pin Connection Function
5.6.7.8 GND +24VDC RETURN
1.2.3.4 +V1 +24VDC OUTPUT
Note:  CON103 -- XH CONNEETION, TYPE : pitch2.5mm





Table 16  Pin-CON3Connection And Function

NO. Pin Connection Function
     
3.4 GND +24VDC RETURN
1.2 Vaudio +24VDC OUTPUT

Note:  CON103 -- XH CONNEETION, TYPE : pitch2.5mm


Table 17  Pin-CON4 Connection And Function

NO. Pin Connection Function
1. 2 GND +5V +5VSB +12VDC RETURN
3.4 +5V +5VDC OUTPUT
5 STB SMPS ON/OFF CONTROL(ON = HIGH)
6 +5VSB STANDBY(+5.0VDC) OUTPUT
7.8 +5V +5VDC OUTPUT
9.10.11 GND +5V +5VSB +12VDC RETURN
12.13 +12V +12VDC OUTPUT

Note: CON5 -- VH CONNEETION, TYPE : pitch2.5mm


Table 18  Pin-CON1 Connection And Function

NO. Pin Connection Function
AC-N AC INPUT NUTURE
NC NC
AC-L AC INPUT LINE

Note: CON1 -- VH CONNEETION, TYPE : pitch3.96mm

更多啊啾哇其它产品
>> 啊啾哇MP118TH-C其它
>> 啊啾哇MLT333其它
>> 啊啾哇DDR3 1333其它
>> 啊啾哇 奔腾 G630其它
更多其它其它产品
>> 窗景(WinSign)WS-30A其它
>> 窗景(WinSign)WS-30B其它
>> 窗景(WinSign)WS-40B其它
>> WebDTSA1000其它
>> WebDTSA1350其它
>> WebDTSA3000其它
设为首页网站建设欢迎投稿数字标牌杂志资讯中心本站动态关于数字标牌网网站RSS网站地图友情链接
热点:数字标牌数字告示多媒体信息发布系统广告机户外广告机液晶广告机网络广告机互动广告机触摸屏MLT197
本站实名:数字标牌网 国际域名:www.DS-360.com 版权所有© 2009-2013 深圳中投网络信息技术有限公司
客服:点击这里给我发消息 点击这里给我发消息 点击这里给我发消息 电话:+86-755-33019199(十二线) 传真:+86-755-33010910 邮箱:ds-360@3v.cn